| |
| Crane body for 2 ton chassis having cab-to-axle (C.A.) measurements
of 60", 72", 84",102",108", and 120". Available in standard "V" configuration
compartment models. |
| |
| I. |
OVERALL LENGTH: |
| |
| |
A. 108", 120", 132", 150", 156", 168" |
| |
| II. |
OVERALL WIDTH: |
| |
| |
A. 94-1/2" (95-3/4") |
| |
| III. |
OVERALL HEIGHT: |
| |
| |
A. 48" |
| |
| IV. |
HEIGHT FROM FLOOR TO TOP OF COMPARTMENT: |
| |
| |
A. 30" |
| |
| V. |
FLOOR WIDTH: |
| |
| |
A. 54-1/2" with 6" wide wheel boxes |
| |
| VI. |
COMPARTMENT DEPTH: |
| |
| |
A. 20" |
| |
| VII. |
COMPARTMENT LAYOUT: |
| |
| |
A. "V" configuration - full height vertical compartments front and rear ; horizontal
compartment at center. |
| |
| |
1. Front compartment width........... |
31" - 108, 132, 150, 156, 168 |
| |
a. Front compartment width........... |
25" - 120 only |
| |
2. Intermediate compartment width.... |
24" - 132, 150, 156, 168 |
| |
3. Horizontal compartment width...... |
52" - "V" style |
| |
4. Rear compartment width............ |
25" - ALL |
|
| |
| VIII. |
UNDER STRUCTURE: |
| |
| |
A. Front cross member - 3" x 5" x 7 ga. structural steel tubing; |
| |
B. Rear cross member - 3" x 5" x 7 ga. full width structural steel tubing. |
| |
C. Intermediate cross members - 3" x 5" x 7 ga. full width square steel tubing at the front
and rear of wheel well. Bodies longer than 120" have additional floor width cross members
forward of the wheel well. |
| |
D. Longitudinal stiffeners - 3 3" x 3" 10 ga. formed channels from rear intermediate forward.
4 to the rear. |
| |
E. Floor - 3/16" safety treadplate steel. |
| |
| IX. |
COMPARTMENT CONSTRUCTION: |
| |
| |
A. Front end panels - 14 ga. A40 galvannealed steel. |
| |
B. Rear end panels - 12 ga. A40 galvannealed steel with 12 ga. treadplate steel overlays. |
| |
C. Bottom panels - 14 ga. A40 galvannealed steel. |
| |
D. Top panels - 14 ga. A40 galvanneal steel with 12 ga. treadplate steel overlays. |
| |
E. Intermediate panels - 16 ga. A40 galvannealed steel. |
| |
F. Horizontal compt. bottom panel - 14 ga. A40 galvannealed steel. |
| |
G. Fender panel - 12 ga. A40 galvannealed steel with 14 ga. A40 galvannealed steel rolled
fenderettes. Further reinforced with diagonal structural tubing. |
| |
H. Back panel - 14 ga. A40 galvannealed steel with 12 ga. treadplate steel overlays. |
| |
I. Rubrail - 14 ga. A40 galvannealed steel. Outside edge of rubrail has 3/8" hem for
additional strength. |
| |
| X. |
FRONT BULKHEAD: |
| |
| |
A. 14 ga. A40 galvannealed steel with formed top rail and three die formed reinforcing ribs.
Lower rib is designed for floor drainage. Inside has a 12 ga. treadplate steel overlay. |
| |
| XI. |
DOOR CONSTRUCTION: |
| |
| |
A. Double panel construction of 20 ga. inner panel and 18 ga. outer panels. A40
galvannealed steel with high impact polystyrene honeycomb stiffener. Lower interior
cavity of doors are treated with automotive type rust preventive coating. |
| |
B. Latch - galvannealed rotary type paddle handle, tamper proof lock, fully weather
proof sealed galvannealed housing, riveted to door for ease of replacement. 1 pt. "T"
and 3 pt. "T" latches are also available as well as stainless steel. |
| |
C. Striker bolt - adjustable and arranged to lock insideprimary seal. |
| |
D. Hinge - full length with 5/16" dia. stainless steel concealed hinge pin with stainless steel
hinge blocks, and oilite bushings. One block welded with other block bolted for ease of
door replacement. |
| |
E. Door seal - full perimeter sealing flange with positive continuous contact with seal.
Primary door seal is automotive type neoprene. |
| |
F. Door holders - heavy duty double spring retainer on all vertical compartments. Cable
stays on both horizontal doors. |
| |
| XII. |
TRAYS & SHELVES: |
| |
| |
A. (4) front compartment and (1) horizontal compartment divider trays Standard. Trays
are 16 ga. galvanized steel , 2" lip front and rear with divider slots on 2" centers. Vertical
and horizontal compartment trays are adjustable via clips on 4" centers. |
| |
B. (1) non-crane rear compartment shelf - standard. 1" lip on either end may be installed so
lip is up or down. Made of the same material as divider trays and also adjustable on 4"
centers. |
| |
| XIII. |
CRANE COMPARTMENT: |
| |
| |
A. Reinforcement - 3/8" structural plate in front,rear, and back with (2) 1/2" steel mounting
plates (one inside compt. and one on outside of compt. top. This is welded to rear and
intermediate cross members and further supported by a 7 ga. fixed shelf between the
uprights. Outriggers should be mounted to this full width support (available from crane
manufacturer). |
| |
| XIV. |
PAINT: |
| |
| |
A. Entire body underside and door interiors covered with automotive type undercoating
meeting OSHA and NFDA specifications. |
| |
B. Pre-Paint Preparation |
| |
| |
1. All product surfaces cleaned with high pressure / high temp. power
wash system. (Fremont Industries 608PF) for maximum adhesion
and added rust and corrosion protection. |
| |
2. All galvanneal surfaces where grinding is required (e.g. to dress
welds) and any non-galvanneal steel that does not get undercoat
protection (e.g. treadplate floor) receives a vinyl wash primer
coating (.05-1.0 mil.) for added rust and corrosion protection
and superior adhesion (Sherwin-Williams E2-G973). |
|
| |
C. Primer |
| |
| |
1. Interior and exterior - two component high solid acrylic urethane
primer sealer (Sherwin - Williams "Prime Shield") , cured with
VIC amine generator licensed through Sherwin-Williams , DFT
1.5-2.0 mils. |
|