| |
| I. |
DIMENSIONS: |
| |
| |
Lengths: 8'6", 9'6", 10'6", 12'6", 14'6", 15'6", 16'6", 18'6", 20'6", 22'6", and 24'6", 26'6" |
| |
Widths: 82", 96" and 102" |
| |
| II. |
FRONT OUTRAIL: |
| |
| |
A. 6" deep. |
| |
B. 11 ga. (.120") high strength steel. |
| |
C. Four 12 ga. (.105") 2 x 4 stake pocket reinforcement inserts sized for 2x4 lumber or
steel stakes. |
| |
D. Gusseted to the runsills. |
| |
E. No welding to face of outrail, therefore no weld through marks on face to mar finish. |
| |
| III. |
SIDE OUTRAIL: |
| |
| |
A. 6" deep. |
| |
B. 11 ga. (.120") high strength steel. |
| |
C. 12 ga. (.105") 2 x 4 stake pocket reinforcement inserts on 24" centers. The number of
pockets varies with the length of the platform. Sized for 2x4 lumber or steel stakes. |
| |
D. No welding to face of outrail, therefore no weld through marks on face to mar finish. |
| |
| IV. |
REAR OUTRAIL: |
| |
| |
A. 6" deep. |
| |
B. 11 ga. (.120") high strength rollformed steel. |
| |
C. Four 12 ga. (.105") 2 x 4 stake pocket reinforcement inserts. Sized for 2x4 lumber or
steel stakes. |
| |
D. Gusseted to the runsills. |
| |
E. No welding to face of outrail, therefore no weld through marks on face to mar finish. |
| |
| V. |
FLOOR AND UNDERSTRUCTURE: |
| |
| |
A. 11 ga. (.120") high strength rollformed "C" section cross sills, 4-3/16" high. |
| |
B. Cross sills are situated on 12" centers on platforms 14' and longer. On platforms shorter
than 14', cross sills are situated on 16" centers. |
| |
C. Every other cross sill is gusseted to the runsill. Fully gusseted on rear 1/3 of platform
length. |
| |
D. Runsills are made of structural channel: |
| |
| |
1. 8'6" - 9'6" platforms--4" runsills. |
| |
2. 10' 6" and 14'6" platforms--6" runsills. |
| |
3. 15' 6" - 20'6" platforms--7" runsills. |
| |
4. 22' 6" - 26'6" platforms--8" runsills. |
|
| |
E. Floor Options: |
| |
| |
1. Wood |
| |
- 2"x6" (nom.) tongue and groove joint, kiln dried,#1 dense
southern yellow pine floor boards which are attached to the cross
sills with trailer-type torx screws. |
| |
- flooring is CCA pressure treated which is forced deep into the
wood's fibers through a thorough impregnation process, then
finish painted with the platform assembly for further protection. |
| |
2. Smooth Steel |
| |
- 10 ga. (.135"), 7 ga. (.179") or 1/4" (0.25") smooth steel
(welded to crossmembers) |
| |
3. Treadplate Steel |
| |
- 1/8" (.125") or 3/16" (.188") treadplate steel (welded to
crossmembers) |
| |
4. Treadplate or smooth steel over wood. |
|
| |
| VI. |
LIGHTING: |
| |
| |
A. Lights are completely recessed into outrail. |
| |
B. Two clearance lights per corner. (Amber/front) (Red/rear) |
| |
C. Three-light (identification) cluster in rear outrail. |
| |
D. Rubber grommet mounted; high impact reflectorized lenses. |
| |
E. Plug-in wire harness. |
| |
F. Weather-tight installation. |
| |
G. All reflectorized lights meet applicable federal standards (FMVSS 108). |
| |
| VII. |
PAINT: |
| |
| |
A. Black rust inhibitive primer. |
| |
B. Black urethane topcoat paint is standard. |
| |
C. Red and white urethane topcoat paints also available. |
| |
D. Entire body underside covered with automotive type undercoating meeting OSHA and NFDA specifications. |
| |
| VIII. |
WEIGHTS: |
| |
| |
See Appendix "D". |