| |
| I. |
GENERAL: |
| |
| |
A. Service body Hi Roof option is designed to fit 40" high service bodies. They can be
factory installed or attached in the field. (Note: Hi Roof for field installation will be
delivered in sectionalized assemblies.) |
| |
| II. |
OVERALL LENGTH: |
| |
| |
A. 96", 108" and 132" |
| |
| III. |
OVERALL WIDTH: |
| |
| |
A. 5" narrower than body each side: 68 1/2", 78 1/2", & 84 1/2" |
| |
B. Optional full width each side, 78 1/2", 88 1/2", 84 1/2" |
| |
| IV. |
INSIDE HEIGHT: |
| |
| |
A. 54", 60", 72" |
| |
| V. |
OVERALL HEIGHT: (including service body) |
| |
| |
A. 54" High model - 69 1/2" |
| |
B. 60" High model - 75 1/2" |
| |
C. 72" High model - 87 1/2" |
| |
| VI. |
ROOF: |
| |
| |
A. One piece top section 20 ga. A40 galvannealed steel. Formed to wrap over side panel
top rails to shed water. |
| |
B. Inside roof bows, 16 ga. galvannealed steel. |
| |
| VII. |
REAR HEADER: |
| |
| |
A. 14 ga. A40 galvannealed steel formed. Holder for rear door stays incorporated. |
| |
| VIII. |
BULKHEAD: |
| |
| |
A. 16 ga. A40 galvannealed steel formed. |
| |
B. Bulkhead stiffener is 16 ga. A40 galvannealed steel. (2) stiffeners used on 72" high
model, (1) used on 54" & 60". |
| |
C. Window is 14" high x 30" wide x 3/16" tempered glass installed with continuous rubber
gasket. Located to match truck rear window. |
| |
| IX. |
SIDE PANELS: |
| |
| |
A. Full length die formed "V" ribs on 12" centers incorporated into side panel for strength,
16 ga. A40 galvannealed steel. |
| |
B. Top corner of side panel formed at 45 degrees to meet roof and accommodate optional
skylight windows. |
| |
| X. |
END PANELS: |
| |
| |
A. Formed to match side panels 14 ga. A40 galvannealed steel. |
| |
| XI. |
SHELVING: |
| |
| |
A. Formed 2" front retaining lip with additional 5/8" return for added strength. 16 ga. A40
galvannealed steel. |
| |
B. 72" high model - Two shelves per side in addition to compartment top. |
| |
C. 54" & 60" high models - One shelf per side in addition to compartment top. |
| |
D. Shelf retainer rails welded to rear edge of compartment top to create an additional shelf.
16 ga. A40 galvannealed steel with formed 2" lip with additional 5/8" return to match
shelves. |
| |
| XII. |
REAR DOORS: |
| |
| |
A. Dual rear doors with 12" wide x 15" high x 3/16" safety glass installed with continuous
rubber seal. |
| |
B. Double panel construction of 20 ga. A40 galvannealed steel with high impact polystyrene
honeycomb stiffener. Lower interior cavity of doors treated with automotive type rust
preventative. |
| |
C. Latch - zinc plated 3 point "T" handle twist latch, tamper proof lock, fully weather proof
sealed galvannealed housing, riveted to door for ease of replacement. |
| |
D. Striker plates - cam action twist latch and rods to lock in place against adjustable strikers
to insure primary seal. |
| |
E. Hinge - full length galvannealed hinge with stainless steel hinge pin. |
| |
F. Door seal - full perimeter sealing flange with positive continuous contact with seal. Primary
door seal is automotive type neoprene. |